- Target Muscle Group
- Exercise TypeStrength
- Equipment RequiredBarbell
- Force TypePush (Bilateral)
- Experience LevelBeginner
- Secondary Muscles
Target Muscle Group
Close Grip Pin Press Overview
The close grip pin press is a variation of the close grip bench press and is used to directly target the muscles of the triceps. The exercise will also indirectly target the chest and shoulders.
The close grip pin press is an excellent exercise to train power since you will be pushing the weight used from a dead stop. The addition of pins also allows the lifter to use slightly heavier weight than they might performing the traditional close grip bench press variation.
Close Grip Pin Press Instructions
- Set the safeties in a rack to just above chest height while supine.
- Lie flat on a bench and set your hands at shoulder width.
- Set your shoulder blades by pinching them together and driving them into the bench.
- Take a deep breath and allow your spotter to help you with the lift off to maintain tightness through your upper back.
- Let the weight settle and ensure your upper back remains tight after lift off.
- Inhale and allow the bar to descend slowly by unlocking the elbows.
- Lower the bar in a straight line to the pins and pause for 2-3 seconds.
- Push the bar back up in a straight line by pressing yourself into the bench, driving your feet into the floor for leg drive, and extending the elbows.
- Repeat from the pins for the desired number of repetitions.
Close Grip Pin Press Tips
- Technique first, weight second - no one cares how much you bench if you get injured.
- Keep the bar in line with your wrist and elbows and ensure it travels in a straight line. To keep the wrist straight, try to position the bar as low in the palm as possible while still being able to wrap the thumb.
- If you want to keep more tension through the triceps and chest, stop each repetition just short of lockout at the top.
- Don’t worry about tucking the elbows excessively, much of this advice is from geared lifters using suits. A slight tuck on the way down may be advisable for some lifters but other lifters can use an excellent cue from Greg Nuckols that accomplishes the same thing: “Flare and push”.
- Arching may be advisable depending upon your goals but ensure that most of the arch comes from the mid to upper back and not your lower back. If your lower back is cramping as you set up for the lift, you’re out of position and putting yourself at risk for potential injury.
- As the bar descends, aim for your sternum (breastbone) or slightly below depending upon the length of your upper arm to promote a linear bar path.
- Intermediate and advanced lifters may use a thumbless or “suicide” grip but for the majority of lifters, it would be wiser to learn how to bench with the thumb wrapped around the bar at first.
- Fight to the urge to allow the wrists to roll back into extension, think about rolling your knuckles toward the ceiling.
- Experiment with grip width - if your have longer arms you may need to use a slightly wider grip. However, if you’re feeling pressure in the front of the shoulder during the exercise, you may need to widen your grip, improve scapular retraction, or slightly lessen the range of motion via exercises such as floor or board presses.
- Squeeze the bar as tightly as possible to help enhance shoulder stability.
- Some lifters prefer to tuck their toes while other prefer to keep the feet flat to optimize leg drive - experiment with both and see which one feels and allows for greater power production.
- Ensure the shoulder blades remain retracted and don’t allow them to change position as you press.
- Think about trying to push yourself away from the bar instead of pushing the bar off of the pins.
- Tightness through the upper back should be one of your main priorities throughout the course of the lift.
- Ideally, use a spotter to help assist with the lift off to maintain tension through the upper back.
- Keep the feet quiet throughout the lift and utilize leg drive by pushing your feet into the floor and squeezing your glutes to stabilize the pelvis.
- Focus on pulling the bar apart or trying to “bend the bar” to activate some of the intrinsic stabilizers in the shoulder.
- The glutes and shoulder blades should maintain contact with the bench throughout the entirety of the movement.