Exercise Profile
  • Target Muscle Group
  • Exercise TypeStrength
  • Equipment RequiredBarbell
  • MechanicsCompound
  • Force TypePush (Bilateral)
  • Experience LevelAdvanced
  • Secondary Muscles
    Shoulders, Triceps
Target Muscle Group

Chest

Chest Muscle Anatomy Diagram

Band Suspended Kettlebell Bench Press Overview

The band suspended kettlebell bench press is a variation of the barbell bench press and an exercise used to strengthen the muscles of the chest. The band suspended kettlebell bench press also indirectly targets the muscles of the shoulders and triceps.

The band suspended kettlebell bench press requires a lot of shoulder stability from the lifter. The kettlebells will dangle from the barbell via resistance bands and each side will sway during the range of motion.

This instability will help strengthen your push muscles and is especially practical when it comes to sports specific performance. They can also be helpful for those who powerlift, as the accommodating resistance provided by the bands and kettlebells will help lifts train through their sticking points.

Band Suspended Kettlebell Bench Press Instructions

  1. Select your weight and load the bar. Once the bar has been loaded, thread a band around a kettlebell handle, loop the band around the bar, and repeat on both sides.
  2. Lie flat on a bench and set your hands just outside of shoulder width.
  3. Set your shoulder blades by pinching them together and driving them into the bench.
  4. Take a deep breath and allow your spotter to help you with the lift off to maintain tightness through your upper back.
  5. Let the weight settle and ensure your upper back remains tight after lift off.
  6. Inhale and allow the bar to descend slowly by unlocking the elbows.
  7. Lower the bar in a straight line to the base of the sternum (breastbone) and touch the chest.
  8. Push the bar back up in a straight line by pressing yourself into the bench, driving your feet into the floor for leg drive, and extending the elbows.
  9. Repeat for the desired number of repetitions.

Band Suspended Kettlebell Bench Press Tips

  1. Hanging band training is very beneficial for increasing shoulder stability within the bench. If you find that you can’t control the bar due to excessive shaking then try to squeeze the bar harder to increase a phenomenon in the shoulder known as irradiation leading to further shoulder stability.
  2. Technique first, weight second - no one cares how much you bench if you get injured.
  3. Keep the bar in line with your wrist and elbows and ensure it travels in a straight line. To keep the wrist straight, try to position the bar as low in the palm as possible while still being able to wrap the thumb.
  4. If you want to keep more tension through the triceps and chest, stop each repetition just short of lockout at the top.
  5. Don’t worry about tucking the elbows excessively, much of this advice is from geared lifters using suits. A slight tuck on the way down may be advisable for some lifters but other lifters can use an excellent cue from Greg Nuckols that accomplishes the same thing: “Flare and push”.
  6. Arching may be advisable depending upon your goals but ensure that most of the arch comes from the mid to upper back and not your lower back. If your lower back is cramping as you set up for the lift, you’re out of position and putting yourself at risk for potential injury.
  7. The bar should touch your chest with every single repetition. If you want to overload specific ranges of motion, look into board presses or accommodating resistance with chains or bands.
  8. As the bar descends, aim for your sternum (breastbone) or slightly below depending upon the length of your upper arm to promote a linear bar path.
  9. Fight to the urge to allow the wrists to roll back into extension, think about rolling your knuckles toward the ceiling.
  10. Experiment with grip width - if your have longer arms you may need to use a slightly wider grip. However, if you’re feeling pressure in the front of the shoulder during the exercise, you may need to widen your grip, improve scapular retraction, or slightly lessen the range of motion via exercises such as floor or board presses.
  11. Squeeze the bar as tightly as possible to help enhance shoulder stability.
  12. Some lifters prefer to tuck their toes while other prefer to keep the feet flat to optimize leg drive - experiment with both and see which one feels and allows for greater power production.
  13. Ensure the shoulder blades remain retracted and don’t allow them to change position as you press.
  14. The bar should descend under control and touch the lifter’s chest - no bouncing or excess momentum.
  15. Think about trying to push yourself away from the bar instead of pushing the bar off of you.
  16. Tightness through the upper back should be one of your main priorities throughout the course of the lift.
  17. Ideally, use a spotter to help assist with the lift off to maintain tension through the upper back.
  18. Keep the feet quiet throughout the lift and utilize leg drive by pushing your feet into the floor and squeezing your glutes to stabilize the pelvis.
  19. Focus on pulling the bar apart or trying to “bend the bar” to activate some of the intrinsic stabilizers in the shoulder.
  20. The glutes and shoulder blades should maintain contact with the bench throughout the entirety of the movement.
0 Comments